-Honda Gas Powered Winder
- The ProTatch wire winder comes with reliable 5.5 hp. Honda pull start gas engine.
- Motor carries a 3 year warranty, through Honda.
- The handle on the manual wire guide, can be moved from right to left, depending on what side you are working the machine from.
- Clutch can be operated from either side.
- Removable shield's on both the belt drive and the chain drive. ( easy to service )
- Standard with manual wire guide.
- Tie off hooks to secure it to your truck or trailer when rolling wire.
- Lift hook, located centrally on the machine to use if needed to load.
- Split reel is designed to be used over and over.
- Reel is designed with 4 tie wire points to place tie wires in before starting to roll wire.
- Yellow split reel is the same reel we use on all our winders. However, the high tensile reel will not fit on this unit. If you are rolling high tensile with this unit, we recommend the 8" center solid reel.
After you service your new gas powered winder, and it is ready to use the first time, you may need to adjust the motor on the motor mount base to the right tension on the belt, as it takes a while to season the belt and get the best performance from your new winder.
When you receive your gas winder, it will be assembled on a pallet and will only need to have the engine serviced, with oil before it is ready to run.
Use 10-30 motor oil ( service on a regular basis, depending on use )
- The ProTatch wire winder comes with reliable 5.5 hp. Honda pull start gas engine.
- Motor carries a 3 year warranty, through Honda.
- The handle on the manual wire guide, can be moved from right to left, depending on what side you are working the machine from.
- Clutch can be operated from either side.
- Removable shield's on both the belt drive and the chain drive. ( easy to service )
- Standard with manual wire guide.
- Tie off hooks to secure it to your truck or trailer when rolling wire.
- Lift hook, located centrally on the machine to use if needed to load.
- Split reel is designed to be used over and over.
- Reel is designed with 4 tie wire points to place tie wires in before starting to roll wire.
- Yellow split reel is the same reel we use on all our winders. However, the high tensile reel will not fit on this unit. If you are rolling high tensile with this unit, we recommend the 8" center solid reel.
After you service your new gas powered winder, and it is ready to use the first time, you may need to adjust the motor on the motor mount base to the right tension on the belt, as it takes a while to season the belt and get the best performance from your new winder.
When you receive your gas winder, it will be assembled on a pallet and will only need to have the engine serviced, with oil before it is ready to run.
Use 10-30 motor oil ( service on a regular basis, depending on use )
Removable Wire Reels
Designed to be used on high tensile, its 8” center you will not roll the high tensile wire as tight, in a small coil when rolling. Capacity is 1 mile of wire. The outside diameter of this reel is 20".
The 4” center standard reel measures 20” in diameter with a 4" center, and is designed to be used on any type of wire. It will comfortably hold 1 mile of smooth or 1/2 mile of barbed wire.
The 4” mini solid reel is 12” in diameter with a 4" center, designed to hold smooth or barbed wire. It will comfortably hold 1/2 mile smooth wire.
All 3 designs are manufactured of steel with baked on premium powder coat finish.
SOLID REEL PART NUMBERS & DIMENSIONS NS-1752 (4"MINI): 12" OUTSIDE DIAMETER WITH 4" CENTERNS-1754 (4" CENTER): 20" OUTSIDE DIAMETER WITH 4" CENTERNS-1758 (8" CENTER): 20" OUTSIDE DIAMETER WITH 8" CENTER
Designed to be used on high tensile, its 8” center you will not roll the high tensile wire as tight, in a small coil when rolling. Capacity is 1 mile of wire. The outside diameter of this reel is 20".
The 4” center standard reel measures 20” in diameter with a 4" center, and is designed to be used on any type of wire. It will comfortably hold 1 mile of smooth or 1/2 mile of barbed wire.
The 4” mini solid reel is 12” in diameter with a 4" center, designed to hold smooth or barbed wire. It will comfortably hold 1/2 mile smooth wire.
All 3 designs are manufactured of steel with baked on premium powder coat finish.
SOLID REEL PART NUMBERS & DIMENSIONS NS-1752 (4"MINI): 12" OUTSIDE DIAMETER WITH 4" CENTERNS-1754 (4" CENTER): 20" OUTSIDE DIAMETER WITH 4" CENTERNS-1758 (8" CENTER): 20" OUTSIDE DIAMETER WITH 8" CENTER